LTC4263
13
4263fe
APPLICATIONS INFORMATION
Power Management
The LTC4263 includes a power management feature
allowing simple implementation of power management
across multiple ports driven by a single power supply. The
PWRMGT pins of all LTC4263 devices are tied together
along with an RC network to prevent over-allocation of
power in a multi-port system.
Immediately following classi cation, the LTC4263 performs
a power management check to ensure power is available
to supply the newly classed PD. The allocated power is
represented by the voltage on the shared PWRMGT node
and the LTC4263 checks the allocated power by measur-
ing this voltage. If the PWRMGT voltage is less than 1V ,
there is power available and the power needs of the new
PD are added to the already allocated power on the node.
To allocate power, a current proportional to the power
needs for the new PD is sourced out of the PWRMGT pin
(Table 2).
Table 2. LTC4263 Power Management
IEEE 802.3af
CLASS
PSE OUTPUT
POWER REQUIRED
LTC4263 PWRMGT
CURRENT
0, 3, 4
15.4W
72.3糀
2
7W
32.8糀
1
4W
18.8糀
For multiple LTC4263s implementing power management,
the PWRMGT pins are connected together and to a RC
network connected to V
SS
as shown in Figure 5. The value of
R
PM
represents the full load output capability of the system
power supply (P
FULL_LOAD
). Select a 1% resistor to set the
full load output power using the following formula:
R
k
W
P
PM
FULL LOAD
=
213 ?"
_
The LTC4263 power management uses pulse width
modulation to set the power requirements of each PD.
Capacitor C
PM
is used as a lowpass lter to generate the
average power requirement for all PDs in the system. Set
C
PM
to 1糉.
If power management is not used, tie PWRMGT to V
SS
.
When additional current is added to the PWRMGT node,
the voltage rises toward the 1V threshold. After adding
current, the LTC4263 veri es that the power supply is not
over-allocated by verifying the node voltage remains below
1V. If the voltage is below 1V , the LTC4263 proceeds to
power the port. If over 1V , the current is removed from
the node, port powering is aborted, and the LTC4263 goes
back into detection mode.
Figure 5. PWRMGT Pin Connections
PWRMGT
V
SS
LTC4263
PWRMGT
V
SS
LTC4263
PWRMGT
V
SS
LTC4263
PWRMGT
V
SS
V
SS
LTC4263
4263 F05
C
PM
1糉
R
PM
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
LTC4268IDKD-1#PBF
IC PD HIGH POWER W/CNTRL 32-DFN
LTC4274CUHF#PBF
IC CONTROLLER POE 38-QFN
LTC4280CUFD#PBF
IC CONTROLLER HOT SWAP QFN-24
LTC4300-1IMS8#TRPBF
IC HOTSWAP 2WIRE BUS BUFFR 8MSOP
LTC4300A-2IMS8#TRPBF
IC BUFFER BUS 2WR HOTSWAP 8-MSOP
LTC4301IDD
IC BUFFER BUS HOTSWAP 2WR 8DFN
LTC4301LIDD#TRPBF
IC BUFFER BUS HOTSWAP 2WR 8DFN
LTC4302IMS-1#TRPBF
IC BUFFER 2-WIRE BUS 10-MSOP
相关代理商/技术参数
LTC4263IS-PBF
制造商:LINER 制造商全称:Linear Technology 功能描述:Single IEEE 802.3af Compliant PSE Controller with Internal Switch
LTC4263IS-TRPBF
制造商:LINER 制造商全称:Linear Technology 功能描述:Single IEEE 802.3af Compliant PSE Controller with Internal Switch
LTC4264
制造商:LINER 制造商全称:Linear Technology 功能描述:Synchronous No-Opto Flyback Controller
LTC4264CDE
制造商:LINER 制造商全称:Linear Technology 功能描述:High Power PD Interface Controller with 750mA Current Limit
LTC4264CDE#PBF
功能描述:IC CNTRLR PD INTERFACE 12-DFN RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC4264CDE#TRPBF
功能描述:IC INTERFACE 802.3AT 12-DFN RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC4264IDE
制造商:LINER 制造商全称:Linear Technology 功能描述:High Power PD Interface Controller with 750mA Current Limit
LTC4264IDE#PBF
功能描述:IC CNTRLR PD INTERFACE 12-DFN RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND